Table Of Contents

Next topic

3D-info

Ben’s HobbyCorner

Welcome
This is my homepage, showing things I am working on for a hobby. To do a quick update, not losing a lot of time, I use Sphinx Python Documentation Generator. I also deleted the 80C535 project on this homepage.
Who am I?
Ben Zijlstra. Network Engineer (mainly Cisco) at a large ICT-company in The Netherlands. My first step in electronics was when my father gave me an Philips EE experimental box. Must have been more than 50 years ago. Check LinkedIn for the companies I have been working for (and the present one).

Note

What’s new and when was the last update of this homepage?

November 25 2014:

added 3d-info pictures

added Cathodic Dis-bonding tester

added Wizfi210 Arduino Mega shield

added A4988 steppermotor driver with Bascom-AVR

Hardware

Arduino

My own shields

_images/9dof.jpg

9 degrees of freedom. Attitude and heading Inertial Measurement Unit

  • WizFi210 Arduino Mega Shield
_images/wizfi210_02.jpg

Arduino Mega WizFI210 shield

_images/wizfi210_04.jpg

Configuration through a separate RS232-module

_images/wizfi210_05.jpg

WizSmartScript configuration

  • PWM2Volt Arduino Mega shield
_images/pwm2volt.jpg

4 channel, 4 x PWM to 0-10 volt (total 350 mA), to drive LED-drivers. PWM2Volt

3D Printer

Prusa I3

  • Building my own Prusa I3
_images/homepg(3).jpg _images/homepg(4).jpg _images/homepg(5).jpg

3D-printer

Software

Bascom

Bascom-AVR

_images/a4988.jpg

Connection diagram A4988

_images/a4988_2.jpg

Tested on a Sanguinololu 3D printer controller

_images/etherrape.jpg

Etherrape with an Atmega644

  • Cathodic Dis-bonding Tester - webbased

This is a Cathodic Dis-bonding Tester. This device, during a month during test, tests the quality of paint. Two probes. Through the display and three keys the parameters can be filled in, voltage to put on the probes. But it is also web based and can be configured through the Intra/Internet.

_images/cat1.jpg

Cathodic Disbonding Tester

_images/cat2.jpg
_images/cat3.jpg
_images/cat4.jpg
_images/cat5.jpg

‘Webbased’

_images/ft232_evb.jpg

FT232RL evaluation board with Visual Basic example

_images/xEio1.jpg

AVR Ethernet board from Hugh Duff

_images/webcatx.jpg

WebCat from www.achatz.nl - Ethernut 1.3F compatible

_images/TIGER_ONLINE_x.jpg

WebTiger - STK500 add-on board with ethernet

_images/wiz610wi-evb_2.jpg

Wiz610wi Wiznet wireless module (it is a small Linux-device)

_images/beurs.jpg

Long Wiz810mj board on the Embedded Systems Conference in San Jose

Bascom-8051

_images/IMCU7100EVB.jpg

W7100 programmed in Bascom-8051, including a W7100def.dat file

3D design software

OpenScad

  • Check later, some of my own OpenScad designs

Warning

The owner of Ben’s HobbyCorner may update this website without notice. Products specification and usage may change accordingly. The owner of Ben’s HobbyCorner will not be liable for any mis-information or errors found on this website. All software provided on this website is provided ‘AS IS’ without any warranty expressed or implied. The owner of Ben’s HobbyCorner will not be liable for any damages, costs or loss of profits arising from the usage of these hobby products.